Use your two bikes and painter’s tape to plan a garage wall layout. Check the parked positions, the movement of each bike and the space you need to unload one.
Measure the two bikes you actually store
Start with handlebar width from end to end, including grips or bar-end mirrors. Note how far the pedals, basket and other accessories project, since those parts can touch at different heights. Weigh each bike in the configuration you expect to hang, including anything that stays attached.
The CYFIE 150° swivel bike rack stores one bike vertically and lists a maximum of 55 lb. Check the weight of each bike and the product’s wheel fit guidance before planning the pair. A wide mountain bike and a lighter road bike can require different wall and lifting space even if their wheel sizes look similar.
Tape out the possible mounting spots
Mark the likely wheel centerlines on the wall with painter’s tape. Indicate the approximate top and bottom of each bike using measurements from the actual bikes and the rack instructions. A paper outline of the handlebar span can help you compare a same-height layout with a staggered one.
Treat the tape as a way to compare locations before drilling. The final positions have to land on wall structure suitable for the rack and hardware. If the wall only supports certain positions, widen the layout or try another section of wall instead of forcing the taped spacing.
Allow for the full swivel movement
Imagine each bike facing out as you lift it onto the rack and again as you take it off. The handlebars, saddle and pedals may sweep into the next bike’s space before they reach the parked angle. Leave room for that movement while the other bike stays in its usual position.
The CYFIE rack has three swivel positions. Try the positions separately for each bike once the racks have been installed according to the instructions. Pull down the hanging ring before turning the bike as directed. If a part touches the wall or the neighboring bike, stop and choose a position with more clearance.
Stagger heights only if both bikes remain easy to lift
A small height difference can help handlebars pass each other in some layouts. It can also put a pedal next to the other bike’s spokes. Compare all of those contact points with tape marks before settling on a stagger, and keep the intended wheel rests aligned with their own racks.
Ask each rider to check their reach from the floor. Assign the easiest position to the bike used most often or the rider who needs the most comfortable lift. If reaching the upper rack requires a step stool or an awkward twist under load, use a wider layout at more accessible heights.
Test with the garage in its usual state
Park the car where it normally sits and open the passenger doors. Swing the house door fully, pull out a recycling bin and check any access routes that run past the wall. Leave room to stand with both hands on the bike while you load or unload it.
If the aisle disappears whenever a bike faces outward, try moving the pair down the wall or choosing a different bay. A layout is practical when either bike comes out while the other bike and the car stay put.
Recheck both bikes after installation
Once the racks are secured and checked as directed, load the bikes one at a time. Confirm each wheel is seated, the bike sits securely and its parts clear the neighboring bike in the chosen parked position. Unload each in turn to check the same path in reverse.
Write down the positions that work so everyone in the household can repeat them. Recheck the layout after adding a basket or changing handlebars. If a rack moves on the wall or a bike exceeds the listed limit, stop using that setup until the fit or mounting issue is resolved.
Frequently Asked Questions
How many inches should I leave between two swivel bike racks?
Start with your bikes’ handlebar and pedal clearances, then account for the motion needed to load and swivel each bike. Final spacing depends on the bikes, the wall structure and what sits nearby.
Can I hang two bikes on one CYFIE swivel bike rack?
Plan one compatible bike per rack. For two bikes, use two independently mounted racks and check the weight of each bike against the listed 55 lb maximum.
Is a staggered layout always better?
Use a stagger only when it improves clearance without creating an awkward lift. If both bikes have wide bars or protruding accessories, two lower racks farther apart may be easier to use.
What should I check if the bikes touch when they swivel?
Identify whether the bars, pedals or wheels are making contact. Try a different supported parked position and reassess the unloading path. If there is still interference, increase spacing or choose another wall area.
Explore the products
